Average Reviews:
(More customer reviews)I purchased the MIIIFS stapler to lay approximately 1,700 sq. ft. of 3/4 inch red oak flooring in my new home.After installing well over 1,400 sq. ft. here are some of my observations:
1) The tool makes it very easy for a novice to put down a nice, tight hardwood floor.If the boards are laying tight an easy swing of the mallet is all it takes to fully seat a staple (more on this later).If the board is warped the MIIIFS can stand up to a solid mallet smack without any trouble.The mallet's plastic face, by the way, does not show any signs of cracking so far.
2) The stapler efficiently uses the its air so you do not need a big compressor.I have been using a 1.5 hp unit with a 6 gallon tank.Output is set at 85 psi.I doubt such a small compressor could supply two nailers simultaneously, but it handles one quite nicely.
3) The stapler did develop a small air leak near the top shortly after I began using it.The amount of leaking is small (based on psi drop at the compressor) but does make a distracting noise.This leak does not affect the function or reliability.
4) At your starting wall you need to face nail the flooring until you get about 6 inches from the wall.After that you'll have enough room to get the stapler into position.
5) As you approach the far wall the stapler can be used up to the last 13 or 14 inches.
6) As mentioned earlier the tool only requires an easy mallet smack.However, if you don't swing firmly enough the staple will not seat fully.This is usually caused by crowding against the far wall and not having enough room to swing the mallet.
7) The firing knob is too stiff to actuate by hand reliably - the mallet is required.It would have been nice if there was a way to trigger the stapler by hand then you could use it much closer to the far wall.
8) I have not had any problems with jamming.The unit I've been using has reliably shot every staple right down to the very last one in the magazine.
9) I have heard some rumors of staple-style flooring nailers damaging the floor's tongue.After closely examining several hundred staples in oak I'd say that about 2 or 3 percent show any signs of tongue damage.Some of this infrequent damage is due to stapling through a knot or due to handling.Some is due to the MIIIFS.I'm not sure how this compares to nail-style nailers.Anytime you send a fastener through kiln dried hardwood you're bound to have some occassional splitting.
Would I buy the MIIIFS again?You bet I would.Despite its few minor shortcomings this tool has saved me a LOT of work and the price is lower than other pnuematic nailers that I've looked at.
Click Here to see more reviews about: Bostitch MIIIFS 1-1/2 Inch to 2 Inch Pneumatic Floor Stapler
Product Description:
The Bostitch MIIIFS Pneumatic Floor Stapler lets you create professional-looking floors quickly and comfortably. Its high-speed pneumatic operation rapidly drives staples into both unfinished and prefinished hardwood flooring, and its long-grip handle allows you to maintain a comfortable posture when working. Tackling prefinished flooring is no problem with the included adapter foot and the extra-wide base plates that drive staples exactly where you want them.
The Bostitch MIIIFS
Pneumatic Floor Stapler
At a Glance:
420 in./lbs. of driving power
High-speed, mallet-actuated operation
Extra-wide base plate for stability and control
Ergonomic design with elongated handle
Adaptor foot and FloorGuard graphite mallet provide stability and control. View larger.
1.5" to 2.0" staples are ideal for
0.5" to 0.75" hardwood flooring. All the Power You Need to Get Jobs Done Quickly
Harness the power of compressed air and complete your stapling jobs quickly and easily. Just connect the Bostitch MIIIFS Pneumatic Floor Stapler to your air compressor for 420 in/lbs of impact at 70-120 PSI. A manual strike will activate the firing action with a lightweight FloorGuard graphite mallet, and a 92-staple magazine will keep you working without interruption.
Comfortable Design Keeps You in Control
Ergonomically designed for ease of use, the MIIIFS features an elongated handle that lets you work in a natural, comfortable position. For control, the extra-wide 1/2- and 3/4-inch interchangeable base plates sit flush against floor boards for stability, so you can drive staples at the proper depth every time. Additionally, a pre-finished floorboard adapter foot won't scuff or scratch floors during installation for a professional-grade result every time.
Lightweight, Durable Construction for Everyday Use
The MIIIFS Pneumatic Floor Stapler's lightweight body and graphite FloorGuard mallet make this tool comfortable enough to wield all day without fatigue. Built for durability, this stapler will withstand the wear and tear of any jobsite.
The Bostitch MIIFS Pneumatic Floor Stapler measures 3.13 x 14.8 x 17.25 inches (WxHxL) and weighs 11.2 pounds. It is covered by a seven-year limited warranty.
About Bostitch
Stanley-Bostitch manufactures premium-quality, innovative fastening tools and fasteners for industrial, construction, and home-improvement applications. Products include pneumatic staplers and nailers; compressors; manual staplers and tackers; coil-fed screw systems; rivet tools; glue guns; a broad assortment of collated nails, screws, staples and specialty fasteners in a variety of materials and finishes; and carton-closing staplers--many of them industry firsts.
What's in the Box
Stapler, FloorGuard graphite mallet, pre-finished-flooring adapter foot, and two base plates (1/2 inch and 3/4 inch).
Get 4% OFF
Want to read more honest consumer review about Bostitch MIIIFS 1-1/2 Inch to 2 Inch Pneumatic Floor Stapler now ?
