K Tool International KTI-72130 3/8" Drive Digital Torque Wrench Review

Average Reviews:

(More customer reviews)I purchased this torque wrench primarily for use on my motorcycle. Some torque values on my VROD are in inch pounds, some in foot pounds, and the rest are Newton meters. With this tool I can go as low as 1 inch pound if needed and switch over to 20 Newton meters w/the push of a couple of buttons.I like the audible tone alerts that increase in volume and change pattern as you get closer to the desired torque value.
The con is that it takes a couple of minutes to learn how to navigate the device and it does not have a power off button. It does shut off after 5min of inactivity, but I prefer to turn things off manually.I would recommend this product and I would purchase this product again.

Click Here to see more reviews about: K Tool International KTI-72130 3/8 Drive Digital Torque Wrench

Product Description:
K Tool International 3/8" Drive Digital Torque Wrench features a non-slip grip, with a rugged durable housing and has high contrast, backlit LCD screen display. It consists of four buttons to operate the tool which is power on/off; unit of measurement, torque target up and torque target down. This wrench quickly switches among three types of measurement, eliminating the need to have three separate tools. It performs consistently and withstands even the most heavy-duty applications.

Get 31% OFF

Want to read more honest consumer review about K Tool International KTI-72130 3/8 Drive Digital Torque Wrench now ?

SK 89039 Superset 33 Piece 1/4-Inch and 3/8-Inch Drive Screwdriver Bit Set Set Review

Average Reviews:

(More customer reviews)I have many snap on,matco,and mac tools.These SK tools are just as good as any of those for a fraction of their cost.It would be very easy to build a nice tool set of SK tools for very little cost,not much more then overrated craftsman tools

Click Here to see more reviews about: SK 89039 Superset 33 Piece 1/4 Inch and 3/8 Inch Drive Screwdriver Bit Set Set

Product Description:
With its durable SuperKrome finish, the SK Hand Tools 33-Piece 1/4-Inch and 3/8-Inch Drive Bit Socket SuperSet provides for long life and maximum corrosion resistance. The through-hole design makes it easier to replace worn or broken bits. Simply pop the old bit out and insert a new replacement bit. The C-Clip retention groove in the hex end provides a secure hold on the bit while in use. These bits are manufactured to rigid standards using high strength S2 steel. High-torque can be achieved with the use of a ratchet, T-handle or spinner handle. With the help of an extension or universal joint, bits can be used in awkward spaces. Made in the U.S.A. and packaged in a molded plastic case, this set comes with a lifetime warranty.
What's in the Box
T10, T15, T20, T25, T27, T30 TORX 1/4-inch drive bit sockets; T40, T45, T50, T55 TORX 3/8-inch drive bit sockets; 1/8-, 5/32-, 3/16-, 7/32-, 1/4-, 5/16-, and 3/8-inch hex bit sockets; 2-, 2-1/2-, 3-, 4-, 5-, 6-, 7-, 8-, and 10-millimeter hex bit sockets; #4, #5, #6 slotted screwdriver bit sockets; #1, #2, #3 phillips screwdriver bit sockets; #2 POZIDRIV screwdriver bit socket.

Get 35% OFF

Want to read more honest consumer review about SK 89039 Superset 33 Piece 1/4 Inch and 3/8 Inch Drive Screwdriver Bit Set Set now ?

Waterloo Industries ML500 Shop Series 5 Drawer Tool Cart - 26.5 Wide Review

Average Reviews:

(More customer reviews)Thank you,
The shipping speed and price, where amazing!I live in Alaska and nothing is ever quick and affordable, your services was both!

The product is great, I don't know much about tools and I was buying this as a gift, the receipent loved it and thought it was of great quality.
Thanks again.

Click Here to see more reviews about: Waterloo Industries ML500 Shop Series 5 Drawer Tool Cart - 26.5 Wide

Product Description:
Reinforced side-wall construction for added strength and durability. Full-extension drawer slides provide complete access to every drawer. External lock bar provides visual proof of security.

Get 7% OFF

Want to read more honest consumer review about Waterloo Industries ML500 Shop Series 5 Drawer Tool Cart - 26.5 Wide now ?

Rapid Reel 150-Foot Two-Wheel Cart Hose Reel GH164-CT Review

Average Reviews:

(More customer reviews)This was my 2nd Rapid Reel.I had ordered this expecting it to be the same as my old one but it was a newer model.I was somewhat disapointed that this newer model was $30 more than the older one and when it arrived seemed more cheaply made.The new one is Aluminum versus steel in the older model.It also required a lot more assembly.In some ways it's better than the old model (lighter, aluminum won't rust) but at the same time the handle seems more rickety because it's not a single piece like the old model and tends to flex where the two pieces connect.The short hose that connects to the reel also seems like a generic 5/8" inch when the older model came with a 3/4" Goodyear hose.All and all it's a solid hose reel and way better than anything plastic, but I think I would have been happier with another one of the older models at $99 instead of this newer model at $129.

Click Here to see more reviews about: Rapid Reel 150-Foot Two-Wheel Cart Hose Reel GH164-CT

Product Description:
The Rapid Reel 150-foot two-wheel cart reel provides an organized means to efficiently store and transport hoses up to 150 feet long. Features include rugged 10-inch pneumatic wheels designed to roll over a variety of different terrain, and a rugged tubular frame for maximum stability. A great alternative to wall-mounted reels, the reel is elevated for comfortable rewinding, and comes with a dual grip handlebar for added user comfort. The included bass swivel comes backed with a 10-year limited warranty. No hose is included.

Want to read more honest consumer review about Rapid Reel 150-Foot Two-Wheel Cart Hose Reel GH164-CT now ?

Biesemeyer 78-431 T-Square Anti-Kickback Snap-In Spreader For Delta Left Tilt Unisaw Table Saw Review

Average Reviews:

(More customer reviews)After reading many articles on table saw kick back, I decided I did not want to be the next victim so I bought the Biesemeyer 78-431 T-Square Anti-Kickback Snap-In Spreader (For Delta Left Tilt Unisaw). I removed the original blade guard and kickback device after one day of use. The blind spots were distracting and aggravating. When it came time to install my dado blade, there was the factory splitter. Aggravating to remove and more aggravating to install and align. Without completing the re-installation, I worked for a few weeks without both.MUCH nicer and no aggravations!

My conscience told me over and over to install a splitter so I bought the 78-431.
Over priced? Yes. Worth it? Yes! What is the cost of a finger or hand? Much more in many ways than the cost of this splitter/ kickback device.DO NOT order the wrong unit.Right tilt and left tilt saws require their own order number.
Installation was non-complex, bigger hands than mine might have some grief but that goes without saying when working in tight spaces.All of the original blade guard hardware must be removed. If you already installed and auxiliary out feed table, you may have to loosen a bolt or two and readjust it when you're done. No big deal.

Keep in mind that the splitter/kickback device is removable and replaceable in seconds; also keep in mind that this splitter is for 1/8" blades only. Thin kerf blades will not work with this unit. A three horsepower and higher saw does not require a thin kerf blade. They are meant for lower horsepower contractor and bench saws since the thin kerf allows for easier cutting pressures.

Some of the earlier Biesemeyer overhead blade guards came with a removable splitter that sold separately for about $30.00.The 78-431 is about $130.00 and more meaty than the thirty dollar freebee.
I use this splitter/kickback device faithfully and never had a problem.Here's to all my fingers!!Thank you Biesemeyer!

Click Here to see more reviews about: Biesemeyer 78-431 T-Square Anti-Kickback Snap-In Spreader For Delta Left Tilt Unisaw Table Saw

Product Description:
The Biesemeyer T-square anti-kickback snap-in spreader increases table saw safety by reducing dangerous kickbacks. This spreader snaps in instantly and removes easily on left-tilt unisaws from several manufacturers. Each spreader has a unique mounting bracket designed to mount to the saw using the existing mounting holes for the saw's factory guard/spreader unit. Once the mounting bracket is installed, the spreader will be aligned with the saw blade every time it is removed and reinserted. Remove the splitter blade quickly by taking out the table insert, pulling on the spring loaded pin and pulling the blade out. Insert the spreader into the mounting bracket until the spring-loaded pin engages the hole in the splitter blade to reinstall.
The Biesemeyer T-square anti-kickback splitter is designed to be used in conjunction with a basket-style blade guard. The splitters are not intended to be used with a thin kerf blade. Minimum saw blade thickness is 1/8 inch.

Get 30% OFF

Want to read more honest consumer review about Biesemeyer 78-431 T-Square Anti-Kickback Snap-In Spreader For Delta Left Tilt Unisaw Table Saw now ?

HOMAK BK06022704 27-Inch 2-Drawer Tool Cart Review

Average Reviews:

(More customer reviews)This came with no dents and seems to be made well im pleased with it. Seems to be worth what we paid for it.

Click Here to see more reviews about: HOMAK BK06022704 27 Inch 2-Drawer Tool Cart

Product Description:
SAVE BIG BUCKS on this 3-drawer Rolling Cart! When you're working on that special project, or heavy into your hobby, it helps to have specific tools in one place, and easily accessible in a convenient movable cart. This 3-drawer Rolling Tool Cart is the answer. It's also handy in garages or workshops with minimal space, where creative organization is key. My bargain buy saves you BIG! 2 full-width drawers for mega-room, equipped with roller ball bearing glides for smooth operation; Locking top compartment keeps tools and projects secure, as well as safe and away from little hands; Bottom storage tray for easy access to your often-used and larger tools; Large locking caster wheels mean no tipping or unauthorized rolling; Measures 27 4/5 x 14 3/5 x 30"h., weighs 60 lbs., 10 ozs. Tool time! Order now to ensure on-time project completion... and BIG smiles! Rolling Tool Cart

Want to read more honest consumer review about HOMAK BK06022704 27 Inch 2-Drawer Tool Cart now ?

5 Tier Chrome Storage Tower (Chrome) (74"H x 24"W x 18"D) Review

Average Reviews:

(More customer reviews)This is a typical wired shelf you might find in a restaurant kitchen. The assembly was intuitive enough to make up for the lackluster instructions. It took about 20 minutes to put together. Highly recommended and works as advertised. It's not a cheap, lightweight shelf that will bend with ease. I also found out from the manufacturer's website that it is coated with the antimicrobial Microban material. I didn't know that until after I bought it. [...] (They edited out the link)
Check out the pictures I put up, too.

Click Here to see more reviews about: 5 Tier Chrome Storage Tower (Chrome) (74H x 24W x 18D)

Product Description:
Made of sturdy 18 gauge steel, which is then chrome plated to achieve the shiny exterior finish. Assembles in minutes without tools. All shelves can be adjusted within 1" increments on the posts. Leveling feet are included so the unit can adjust to slightly uneven surfaces. Available in 74"H x 24"W x 18"D or 74"H x 48"W x 18"D. Casters are available separately in sets of four. The casters are very easy to install, simply unscrew the positioning bolts at the base of the posts and screw in the threaded bolt on each wheel. Typically this can be done by hand, howevera small crescent or open endedwrench willwork the best to tighten the wheels securely. Assembly level/degree of difficulty: Easy.

Want to read more honest consumer review about 5 Tier Chrome Storage Tower (Chrome) (74H x 24W x 18D) now ?